The Superpro AC-1 is a simple solution to controlling temperature, humidity and CO2 inside the growing area, giving you a perfect balance between cost and accuracy.
AC-1 contains a built-in photocell that can activate a CO2 device during the day and is coordinated with the exhaust fans so as CO2 stops emitting when fans come on.
Note: CO2 levels must be measured and regulated by user.
Modes
Mode A: LOWER temperature and DECREASE humidity indepen..
The Superpro DDAC-1 receives information from the sensors and activates external fans, air conditioners, dehumidifiers, heaters, and CO2 equipment as needed to maintain optimum levels for indoor agriculture. Until now, this simple idea was easier said than done.
A 15-amp / 120 or 10-amp / 240 vot circuit breaker and heavy-duty internal construction ensures that the unit will operate for years without fail. We only use high-quality UL / CE listed component..
The Maxi Controller can adjust the output according to the ambient temperature: the lamps are dimmed automatically when the temperature exceeds a maximum pre-defined level.
Using the DimLux with a Maxi Controller enables you to plug the DimLux directly into a wall socket without needing an intervening relay, time delay unit or time switch – which saves you costs.
A DimLux controlled by a Maxi Controller is the only (digital) ballast that does not need to..
Perfect for the AutoGrow IntelliDose system and AutoGrow Mini Dosers An affordable, highly accurate dosing pump for use with the AutoGrow IntelliDose system and both AutoGrow Mini Dosers (EC and pH) single unit...
The new Mini Doser EC nutrient controller can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel.
The controller continuously measures the nutrient concentration in the mixing tank and adds A and B nutrients as required to maintain the EC set point. The controller counts the number of doses and in theevent of the dose count per hour exceeding a set value and alarm can be sounded...
The new Mini Doser continuously measures the pH in the mixing tank and adds either pH lower (acid) or pH raise (alkali) as required to maintain the pH set point. The controller counts the number of doses and in the event of the dose count per hour exceeding a set value an alarm can be sounded. In addition alarms can be set to sound should the pH wander outside user set limits. If the dose count per hour exceeds a user setting, the controller will stop dosi..
These are great little machines aimed at the budget conscious and those who don't need a computer interface. Ideal for hobby gardeners, schools, etc. Even large commercial growers use them - particularly for water pre-treatment (pH) or if they have a trial area with a number of reservoir tanks.
The new Mini Doser can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel...
These are great little machines aimed at the budget conscious and those who don't need a computer interface. Ideal for hobby gardeners, schools, etc. Even large commercial growers use them - particularly for water pre-treatment (pH) or if they have a trial area with a number of reservoir tanks.
The new Mini Doser can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel...
The Bluelab Dosetronic keeps tight control of your vital nutrient solution levels automatically so you have the freedom to tend to the daily needs of your crop.
This is the ultimate answer for accurate and automatic control of EC, pH and temperature in hydroponic systems. The controller is easily programmed with the required values for pH, conductivity and temperature. The dosing intervals are set according to the size of the tank and then it’s ..
The Bluelab Dosetronic keeps tight control of your vital nutrient solution levels automatically so you have the freedom to tend to the daily needs of your crop.
This is the ultimate answer for accurate and automatic control of EC, pH and temperature in hydroponic systems. The controller is easily programmed with the required values for pH, conductivity and temperature. The dosing intervals are set according to the size of the tank and then it’s ..
The CARBON -B1 is designed to cost-effectively control the CO2 level inside a growing area. An extremely accurate NDIR CO2 PPM sensor (part-per-million meter) is combined with a digital microprocessor to create an accurate and simple method to control supplemental CO2 use in a greenhouse. The unit can control CO2 levels up to 2500PPM. The user selects the desired CO2 level to be maintained.
A built-in photocell automatically activates the unit only during..
The GI professional CO2 monitor/controller combines the very latest technology with plug and play operation. We have added a photosensor to detect light and dark, this automaticaly changes the working mode of the controller. Other features include: fully adjustable between 0-2000ppm, wall mountable, extremely accurate external sensor with 3 meter cable & automatic calibration.
The GI controller can be used with CO2 generators, CO2 injection devices, s..
The Ultimate CO 2 Controller.
• Simple to use.
• Four separate modes of operation.
• Can be used with or without Analyser.
• Latest Microprocessor technology.
• Intelligent Multi Stage CO 2 dosing.
• Wall mountable.
• User friendly.
• Full 1 year warranty.
• Low Cost
Carbon Dioxide is one of the most important factors in an indoor growroom or glass house. Photosynthesis is the term used to describe the process by which plants combine CO 2 molecul..
A simple to use, innovative CO² sensor and controller, the Harvest Master CO² Easi Controller monitors the growing environment of your grow room – vital for healthy plant growth!
The operation of CO2 EASi.
CO2 EASi is intelligent control of CO2 and at the same time, an Intelligent Temperature controller when the COOL KIT is attached.
In Light ON periods (Day):
The controller will try to maintain Max co2 high PPM for the longest duration. It aggressively..
The Imperium is a precision feed controller, which offer’s greater control over feeding duration and frequency to match each life-stage in a plants growth. Ideal as part of an irrigation system to water plants for the exact amount of time needed. It allows you to feed little and often which will produce maximum yields and allows the use of more oxygen rich media such as a 50;50 mix of Coco and Clay pebbles that would normally dry out without more regular f..
The Imperium Plus is a precision feed controller featuring an integrated Grasslin segmental timer that can be set to run from as little as 1 second up to 15 minutes, at the push of a button which offer’s greater control over feeding duration and frequency to match each life-stage in a plants growth. Ideal as part of an irrigation system to water plants for the exact amount of time needed. It allows you to feed little and often which will produce maximum yi..
(European version: requires plug adapter)
The D1-PPM Carbon Dioxide controller provides high-end performance, at economy pricing.
Starts by using a highly accurate NDIR CO2 sensor. The CO2 Sensor is located in a remote sensor enclosure that can be positioned up to 5 meters from the main controller.
Included inside the remote sensor enclosure is also a photocell which will detect light levels to activate the CO2 control function ONLY when desired by the ..
Clever monitoring, dosing and data logging of solution pH levels. Made easy.
Sometimes the more you know, the better. And when it comes to managing the pH of your nutrient solution, exact knowledge makes a world of difference.
Our brainy pH controller connect constantly monitors and fine-tunes the pH levels for you. But more than that, it wirelessly data logs to your computer too, putting continuous information at your fingertips. Use the data to make sy..
Please see new version, this version is no longer available.
Fully Automated pH Control of Aqueous Solutions
The pH control dosing pump from prosystemaqua provides fully automated pH control of aqueous solutions in hydroponic and aquaponic systems.
It has been designed specifically for the control of pH in mixing tanks for fertilisation. Its small and precise flow allows for very accurate control of pH levels in your hydroponic system.
It comes fully e..
Was £350 - Now £300
The Superpro AC-1 is a simple solution to controlling temperature, humidity and CO2 inside the growing area, giving you a perfect balance between cost and accuracy.
AC-1 contains a built-in photocell that can activate a CO2 device during the day and is coordinated with the exhaust fans so as CO2 stops emitting when fans come on.
Note: CO2 levels must be measured and regulated by user.
Modes
Mode A: LOWER temperature and DECR..
GroLab™ Doser Kit is a powerful grow controller that allows to fully monitor and automate the feeding solution of your plants. Nutrients control, pH correction, water level warnings, auto tank refill, are some functions of this kit.
This kit also provides the necessary tools to create security systems to react and/or notify if any issues arise.
Remote control, real-time notifications, IP cameras integration... are just some of the perks you get with GroL..
The Superpro AC-1 is a simple solution to controlling temperature, humidity and CO2 inside the growing area, giving you a perfect balance between cost and accuracy.
AC-1 contains a built-in photocell that can activate a CO2 device during the day and is coordinated with the exhaust fans so as CO2 stops emitting when fans come on.
Note: CO2 levels must be measured and regulated by user.
Modes
Mode A: LOWER temperature and DECREASE humidity indepen..
The Superpro DDAC-1 receives information from the sensors and activates external fans, air conditioners, dehumidifiers, heaters, and CO2 equipment as needed to maintain optimum levels for indoor agriculture. Until now, this simple idea was easier said than done.
A 15-amp / 120 or 10-amp / 240 vot circuit breaker and heavy-duty internal construction ensures that the unit will operate for years without fail. We only use high-quality UL / CE listed component..
The Maxi Controller can adjust the output according to the ambient temperature: the lamps are dimmed automatically when the temperature exceeds a maximum pre-defined level.
Using the DimLux with a Maxi Controller enables you to plug the DimLux directly into a wall socket without needing an intervening relay, time delay unit or time switch – which saves you costs.
A DimLux controlled by a Maxi Controller is the only (digital) ballast that does not need to..
Perfect for the AutoGrow IntelliDose system and AutoGrow Mini Dosers An affordable, highly accurate dosing pump for use with the AutoGrow IntelliDose system and both AutoGrow Mini Dosers (EC and pH) single unit...
The new Mini Doser EC nutrient controller can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel.
The controller continuously measures the nutrient concentration in the mixing tank and adds A and B nutrients as required to maintain the EC set point. The controller counts the number of doses and in theevent of the dose count per hour exceeding a set value and alarm can be sounded...
The new Mini Doser continuously measures the pH in the mixing tank and adds either pH lower (acid) or pH raise (alkali) as required to maintain the pH set point. The controller counts the number of doses and in the event of the dose count per hour exceeding a set value an alarm can be sounded. In addition alarms can be set to sound should the pH wander outside user set limits. If the dose count per hour exceeds a user setting, the controller will stop dosi..
These are great little machines aimed at the budget conscious and those who don't need a computer interface. Ideal for hobby gardeners, schools, etc. Even large commercial growers use them - particularly for water pre-treatment (pH) or if they have a trial area with a number of reservoir tanks.
The new Mini Doser can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel...
These are great little machines aimed at the budget conscious and those who don't need a computer interface. Ideal for hobby gardeners, schools, etc. Even large commercial growers use them - particularly for water pre-treatment (pH) or if they have a trial area with a number of reservoir tanks.
The new Mini Doser can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel...
The Bluelab Dosetronic keeps tight control of your vital nutrient solution levels automatically so you have the freedom to tend to the daily needs of your crop.
This is the ultimate answer for accurate and automatic control of EC, pH and temperature in hydroponic systems. The controller is easily programmed with the required values for pH, conductivity and temperature. The dosing intervals are set according to the size of the tank and then it’s ..
The Bluelab Dosetronic keeps tight control of your vital nutrient solution levels automatically so you have the freedom to tend to the daily needs of your crop.
This is the ultimate answer for accurate and automatic control of EC, pH and temperature in hydroponic systems. The controller is easily programmed with the required values for pH, conductivity and temperature. The dosing intervals are set according to the size of the tank and then it’s ..
The CARBON -B1 is designed to cost-effectively control the CO2 level inside a growing area. An extremely accurate NDIR CO2 PPM sensor (part-per-million meter) is combined with a digital microprocessor to create an accurate and simple method to control supplemental CO2 use in a greenhouse. The unit can control CO2 levels up to 2500PPM. The user selects the desired CO2 level to be maintained.
A built-in photocell automatically activates the unit only during..
The GI professional CO2 monitor/controller combines the very latest technology with plug and play operation. We have added a photosensor to detect light and dark, this automaticaly changes the working mode of the controller. Other features include: fully adjustable between 0-2000ppm, wall mountable, extremely accurate external sensor with 3 meter cable & automatic calibration.
The GI controller can be used with CO2 generators, CO2 injection devices, s..
The Ultimate CO 2 Controller.
• Simple to use.
• Four separate modes of operation.
• Can be used with or without Analyser.
• Latest Microprocessor technology.
• Intelligent Multi Stage CO 2 dosing.
• Wall mountable.
• User friendly.
• Full 1 year warranty.
• Low Cost
Carbon Dioxide is one of the most important factors in an indoor growroom or glass house. Photosynthesis is the term used to describe the process by which plants combine CO 2 molecul..
A simple to use, innovative CO² sensor and controller, the Harvest Master CO² Easi Controller monitors the growing environment of your grow room – vital for healthy plant growth!
The operation of CO2 EASi.
CO2 EASi is intelligent control of CO2 and at the same time, an Intelligent Temperature controller when the COOL KIT is attached.
In Light ON periods (Day):
The controller will try to maintain Max co2 high PPM for the longest duration. It aggressively..
The Imperium is a precision feed controller, which offer’s greater control over feeding duration and frequency to match each life-stage in a plants growth. Ideal as part of an irrigation system to water plants for the exact amount of time needed. It allows you to feed little and often which will produce maximum yields and allows the use of more oxygen rich media such as a 50;50 mix of Coco and Clay pebbles that would normally dry out without more regular f..
The Imperium Plus is a precision feed controller featuring an integrated Grasslin segmental timer that can be set to run from as little as 1 second up to 15 minutes, at the push of a button which offer’s greater control over feeding duration and frequency to match each life-stage in a plants growth. Ideal as part of an irrigation system to water plants for the exact amount of time needed. It allows you to feed little and often which will produce maximum yi..
(European version: requires plug adapter)
The D1-PPM Carbon Dioxide controller provides high-end performance, at economy pricing.
Starts by using a highly accurate NDIR CO2 sensor. The CO2 Sensor is located in a remote sensor enclosure that can be positioned up to 5 meters from the main controller.
Included inside the remote sensor enclosure is also a photocell which will detect light levels to activate the CO2 control function ONLY when desired by the ..
Clever monitoring, dosing and data logging of solution pH levels. Made easy.
Sometimes the more you know, the better. And when it comes to managing the pH of your nutrient solution, exact knowledge makes a world of difference.
Our brainy pH controller connect constantly monitors and fine-tunes the pH levels for you. But more than that, it wirelessly data logs to your computer too, putting continuous information at your fingertips. Use the data to make sy..
Please see new version, this version is no longer available.
Fully Automated pH Control of Aqueous Solutions
The pH control dosing pump from prosystemaqua provides fully automated pH control of aqueous solutions in hydroponic and aquaponic systems.
It has been designed specifically for the control of pH in mixing tanks for fertilisation. Its small and precise flow allows for very accurate control of pH levels in your hydroponic system.
It comes fully e..
Was £350 - Now £300
The Superpro AC-1 is a simple solution to controlling temperature, humidity and CO2 inside the growing area, giving you a perfect balance between cost and accuracy.
AC-1 contains a built-in photocell that can activate a CO2 device during the day and is coordinated with the exhaust fans so as CO2 stops emitting when fans come on.
Note: CO2 levels must be measured and regulated by user.
Modes
Mode A: LOWER temperature and DECR..
GroLab™ Doser Kit is a powerful grow controller that allows to fully monitor and automate the feeding solution of your plants. Nutrients control, pH correction, water level warnings, auto tank refill, are some functions of this kit.
This kit also provides the necessary tools to create security systems to react and/or notify if any issues arise.
Remote control, real-time notifications, IP cameras integration... are just some of the perks you get with GroL..