The Superpro AC-1 is a simple solution to controlling temperature, humidity and CO2 inside the growing area, giving you a perfect balance between cost and accuracy.
AC-1 contains a built-in photocell that can activate a CO2 device during the day and is coordinated with the exhaust fans so as CO2 stops emitting when fans come on.
Note: CO2 levels must be measured and regulated by user.
Modes
Mode A: LOWER temperature and DECREASE humidity indepen..
The Superpro DDAC-1 receives information from the sensors and activates external fans, air conditioners, dehumidifiers, heaters, and CO2 equipment as needed to maintain optimum levels for indoor agriculture. Until now, this simple idea was easier said than done.
A 15-amp / 120 or 10-amp / 240 vot circuit breaker and heavy-duty internal construction ensures that the unit will operate for years without fail. We only use high-quality UL / CE listed component..
The Maxi Controller can adjust the output according to the ambient temperature: the lamps are dimmed automatically when the temperature exceeds a maximum pre-defined level.
Using the DimLux with a Maxi Controller enables you to plug the DimLux directly into a wall socket without needing an intervening relay, time delay unit or time switch – which saves you costs.
A DimLux controlled by a Maxi Controller is the only (digital) ballast that does not need to..
Perfect for the AutoGrow IntelliDose system and AutoGrow Mini Dosers An affordable, highly accurate dosing pump for use with the AutoGrow IntelliDose system and both AutoGrow Mini Dosers (EC and pH) single unit...
The new Mini Doser EC nutrient controller can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel.
The controller continuously measures the nutrient concentration in the mixing tank and adds A and B nutrients as required to maintain the EC set point. The controller counts the number of doses and in theevent of the dose count per hour exceeding a set value and alarm can be sounded...
The new Mini Doser continuously measures the pH in the mixing tank and adds either pH lower (acid) or pH raise (alkali) as required to maintain the pH set point. The controller counts the number of doses and in the event of the dose count per hour exceeding a set value an alarm can be sounded. In addition alarms can be set to sound should the pH wander outside user set limits. If the dose count per hour exceeds a user setting, the controller will stop dosi..
Feature packed
This hydroponic doser sets a new benchmark in the small dosing controller market. The Intelli-Dose is absolutely feature packed to enable it to cope with just about any hydroponic system. Just take a look at the specification overleaf.
Simple to operate
The secret to its simplicity is that the controller can be configured to suit various systems and when this is done all of the irrelevant settings disappear from the..
These are great little machines aimed at the budget conscious and those who don't need a computer interface. Ideal for hobby gardeners, schools, etc. Even large commercial growers use them - particularly for water pre-treatment (pH) or if they have a trial area with a number of reservoir tanks.
The new Mini Doser can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel...
These are great little machines aimed at the budget conscious and those who don't need a computer interface. Ideal for hobby gardeners, schools, etc. Even large commercial growers use them - particularly for water pre-treatment (pH) or if they have a trial area with a number of reservoir tanks.
The new Mini Doser can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel...
The irrigation timer is used to control a pump for irrigating crops.
This timer is ideal for scheduled Ebb & Flow systems and normal irrigation droplets or NFT systems.
The pulse time and the interval time can be set separately for day and night irrigation. The unit comes complete in a waterproof housing with hinged lids, compatible mains sockets and a built in light sensor with 4m low voltage cable which detects day/night-time; making it the perfect ..
The Bluelab Dosetronic keeps tight control of your vital nutrient solution levels automatically so you have the freedom to tend to the daily needs of your crop.
This is the ultimate answer for accurate and automatic control of EC, pH and temperature in hydroponic systems. The controller is easily programmed with the required values for pH, conductivity and temperature. The dosing intervals are set according to the size of the tank and then it’s ..
The Bluelab Dosetronic keeps tight control of your vital nutrient solution levels automatically so you have the freedom to tend to the daily needs of your crop.
This is the ultimate answer for accurate and automatic control of EC, pH and temperature in hydroponic systems. The controller is easily programmed with the required values for pH, conductivity and temperature. The dosing intervals are set according to the size of the tank and then it’s ..
The CARBON -B1 is designed to cost-effectively control the CO2 level inside a growing area. An extremely accurate NDIR CO2 PPM sensor (part-per-million meter) is combined with a digital microprocessor to create an accurate and simple method to control supplemental CO2 use in a greenhouse. The unit can control CO2 levels up to 2500PPM. The user selects the desired CO2 level to be maintained.
A built-in photocell automatically activates the unit only during..
The GI professional CO2 monitor/controller combines the very latest technology with plug and play operation. We have added a photosensor to detect light and dark, this automaticaly changes the working mode of the controller. Other features include: fully adjustable between 0-2000ppm, wall mountable, extremely accurate external sensor with 3 meter cable & automatic calibration.
The GI controller can be used with CO2 generators, CO2 injection devices, s..
The Ultimate CO 2 Controller.
• Simple to use.
• Four separate modes of operation.
• Can be used with or without Analyser.
• Latest Microprocessor technology.
• Intelligent Multi Stage CO 2 dosing.
• Wall mountable.
• User friendly.
• Full 1 year warranty.
• Low Cost
Carbon Dioxide is one of the most important factors in an indoor growroom or glass house. Photosynthesis is the term used to describe the process by which plants combine CO 2 molecul..
A simple to use, innovative CO² sensor and controller, the Harvest Master CO² Easi Controller monitors the growing environment of your grow room – vital for healthy plant growth!
The operation of CO2 EASi.
CO2 EASi is intelligent control of CO2 and at the same time, an Intelligent Temperature controller when the COOL KIT is attached.
In Light ON periods (Day):
The controller will try to maintain Max co2 high PPM for the longest duration. It aggressively..
Gravity feed and main pressure irrigation controller
The PLANT!T® Water Timer can be used with mains water from a tap outlet or with a gravity feed system from a tank, water butt or reservoir. Simply select the time you want the water supply to be turned on and off, link up to your irrigation dripper line and the timer will do the rest.
Key Features:
2 easy steps to programme – turn RUN TIME dial to desired irrigation time and turn FRE..
The Imperium is a precision feed controller, which offer’s greater control over feeding duration and frequency to match each life-stage in a plants growth. Ideal as part of an irrigation system to water plants for the exact amount of time needed. It allows you to feed little and often which will produce maximum yields and allows the use of more oxygen rich media such as a 50;50 mix of Coco and Clay pebbles that would normally dry out without more regular f..
The Imperium Plus is a precision feed controller featuring an integrated Grasslin segmental timer that can be set to run from as little as 1 second up to 15 minutes, at the push of a button which offer’s greater control over feeding duration and frequency to match each life-stage in a plants growth. Ideal as part of an irrigation system to water plants for the exact amount of time needed. It allows you to feed little and often which will produce maximum yi..
(European version: requires plug adapter)
The D1-PPM Carbon Dioxide controller provides high-end performance, at economy pricing.
Starts by using a highly accurate NDIR CO2 sensor. The CO2 Sensor is located in a remote sensor enclosure that can be positioned up to 5 meters from the main controller.
Included inside the remote sensor enclosure is also a photocell which will detect light levels to activate the CO2 control function ONLY when desired by the ..
Clever monitoring, dosing and data logging of solution pH levels. Made easy.
Sometimes the more you know, the better. And when it comes to managing the pH of your nutrient solution, exact knowledge makes a world of difference.
Our brainy pH controller connect constantly monitors and fine-tunes the pH levels for you. But more than that, it wirelessly data logs to your computer too, putting continuous information at your fingertips. Use the data to make sy..
Please see new version, this version is no longer available.
Fully Automated pH Control of Aqueous Solutions
The pH control dosing pump from prosystemaqua provides fully automated pH control of aqueous solutions in hydroponic and aquaponic systems.
It has been designed specifically for the control of pH in mixing tanks for fertilisation. Its small and precise flow allows for very accurate control of pH levels in your hydroponic system.
It comes fully e..
The DV-101A is a multifunctional analogue seconds time clock that helps you to water crops time controlled.
Specifications
Dimensions in mm: 210 x 140 x 110.
Voltage: 230 V AC/ 50 Hz.
Max. power: 5 Amps.
Isolation level: IP-44..
The DV-101D is a multifunctional digital seconds time clock that helps you to water crops time controlled.
Specifications
Dimensions in mm: 210 x 115 x 110.
Voltage: 230 V AC/ 50 Hz.
Max. power: 6 Amps.
Isolation level: IP-44
Item NR: S1010..
EndoSan Hydrogen Peroxide test strips are simple and quick to use. They quickly measure peroxide levels in water and provide a visual aid to ensure enough EndoSan is in use.
The low range test strips measure peroxide levels up to 100ppm.
How to use:
Dip for 2 seconds
Shake
Wait 30 seconds
Compare to testing chart
Each vial contains 100 test strips...
EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.
EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.
When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.
Key Benefits
Highly effective biofilm remover
Unrivalled s..
EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.
EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.
When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.
Key Benefits
Highly effective biofilm remover
Unrivalled s..
EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.
EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.
When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.
Key Benefits
Highly effective biofilm remover
Unrivalled ..
The CCH2O X Growlink Nutrient Dosing System Makes Dosing Easy as 1, 2, 3
1. Install with Under Current® System or Reservoir
2. Add Cultured Solutions®
3. Download App & Connect to Tablet or Smartphone
Monitor & Dosing – pH PPM DO Temp
Smart Water Wireless Nutrient Controller
pH, EC/PPM, DO & Temp Probes
2x Tank Level Switches
5x Remote Dosing Pumps (80L/min)
Nutrient Injection & Probe Manifol..
The small & precise flow of the MP810 provides fully automated pH control of aqueous solutions in the hydroponic systems. It has been specifically designed to control the pH in mixing tanks for fertilization.
The peristaltic pump allows you to maintain the ideal pH values in your tank. After selecting the desired pH setting from 5.5 to 9.5 pH, the pH controller measures the pH value of the solution & automatically adds pH adjustment (acid or alkal..
A stock concentrate powder for fertilizer injectors. DOS A – DOS is a two-part concentrated nutrient formula for use with proportionate mixers (DOSATRON). It is the same great quality as our one-part base just divided into two-parts to maintain balance as a stock concentrate. At a dilution rate of 1:100, 100 lbs of DOS will treat 12,000 gallons of water.
The concentrate containers will be mixed as follows: Part A: 360 grams/gallon Part B: 240 grams/gallon..
A stock concentrate powder for fertilizer injectors. DOS A – DOS is a two-part concentrated nutrient formula for use with proportionate mixers (DOSATRON). It is the same great quality as our one-part base just divided into two-parts to maintain balance as a stock concentrate. At a dilution rate of 1:100, 100 lbs of DOS will treat 12,000 gallons of water.
The concentrate containers will be mixed as follows: Part A: 360 grams/gallon Part B: 240 grams/gallon..
Provide increased quality, along with making the process of blending and dispensing nutrients easier and more accurate.
The Nutrient Delivery System is a simplistic system made up of four main panel sections which can be arranged to accommodate a wide variety of fertigation programs. With total control in mind, customizing the entire panel is easy based on your personal nutrient program! The Nutrient Delivery System thrives anywhere, from greenhouse envir..
Maintaining the correct pH of plant soil or hydroponics nutrient solution is an ongoing task. Macro and micro nutrients, as well as calcium and magnesium bloom boosters, require the correct pH for absorption into the plants root system.
The HI-981412 Groline pH Dosing System, easily assimilates into a nutrient/fertiliser system for soil and hydroponics.
It precisely monitors the pH using the HI-10063 pH/temperature probe and simultaneously controls the a..
Maintaining the correct pH of plant soil or hydroponics nutrient solution is an ongoing task. Macro and micro nutrients, as well as calcium and magnesium bloom boosters, require the correct pH for absorption into the plants root system.
The HI-981412 Groline pH Dosing System, easily assimilates into a nutrient/fertiliser system for soil and hydroponics.
It precisely monitors the pH using the HI-10063 pH/temperature probe and simultaneously controls the a..
HI-981412-00 GroLine pH dosing system with HI-10063 pH probe
Maintaining the correct pH of plant soil or hydroponic nutrient solution is an ongoing task. Macro and micro nutrients, as well as calcium and magnesium bloom boosters, require the correct pH for absorption into the plants root system.
The HI-981412 Groline pH Dosing System, easily assimilates into a nutrient/fertiliser system for soil and hydroponics.
It precisely monitors the pH using the HI..
HI-981413-00 GroLine EC/TDS/Temp Nutrient dosing system with HI-30033 conductivity probe
The HI-981413 uses an amperometric conductivity sensor for measuring the amount of fertiliser in the solution. The meter can be programmed to display results as EC (electrical conductivity) or as TDS (total dissolved solids). The EC results are displayed as mS/cm while TDS is displayed as ppm with a selectable conversion factor from 0.45 to 0.99.
The HI-981413 was de..
The HI-981413 uses an amperometric conductivity sensor for measuring the amount of fertiliser in the solution. The meter can be programmed to display results as EC (electrical conductivity) or as TDS (total dissolved solids). The EC results are displayed as mS/cm while TDS is displayed as ppm with a selectable conversion factor from 0.45 to 0.99.
The HI-981413 was developed to be an inexpensive solution for the horticulturist to maintain the ideal fertili..
The HI-981413 uses an amperometric conductivity sensor for measuring the amount of fertiliser in the solution. The meter can be programmed to display results as EC (electrical conductivity) or as TDS (total dissolved solids). The EC results are displayed as mS/cm while TDS is displayed as ppm with a selectable conversion factor from 0.45 to 0.99.
The HI-981413 was developed to be an inexpensive solution for the horticulturist to maintain the ideal fertili..
Was £350 - Now £300
The Superpro AC-1 is a simple solution to controlling temperature, humidity and CO2 inside the growing area, giving you a perfect balance between cost and accuracy.
AC-1 contains a built-in photocell that can activate a CO2 device during the day and is coordinated with the exhaust fans so as CO2 stops emitting when fans come on.
Note: CO2 levels must be measured and regulated by user.
Modes
Mode A: LOWER temperature and DECR..
The fertilization reference
More efficient
An optimized design
Really adapted to the evolution of practices and treatments
Highly ergonomic adjustment
Specifications:
Injection range 0,03 - 0,3 % 1:3000 - 1:333]
Water flow range 10 l/h - 3 m3/h
Operating water pressure 0,3 - 6 bar
Concentrated additive injection 0,003 l/h - 9 l/h
Stroke volume ~ 0,53 l
Connections NTP-BSP 3/4'' M Ø 20x27mm
Hose PE Ø 4x6 - Lg 1,75m..
The D20 GL range meets treatment needs from 1 to 20 m3.
Proportional dosing and without electricity
Proportional dosing dependent on water flow
Specifications:
Injection range 0,2 - 2 % [1:500 - 1:50]
Water flow range 1 - 20 m3/h
Operating water pressure 0,12 - 10 bar
Concentrated additive injection 2 - 400 l/h
Stroke volume ~ 5 l
Connections Compression fittings Ø 63mm PE
Hose PVC Ø 16x22mm - Lg 1,80m..
The standard dosing range D07 meets the dosing requirements for flow rates from 5 to 700 l/h.
Proportional dosing and without electricity
Proportionality dependent on water flow
Compact ergonomics
Outlet injection
Specifications:
Injection range 0,15 - 1,25 % [1:666 - 1:80]
Water flow range 5 l/h - 0,7 m3/h
Operating water pressure 0,3 - 6 bar
Concentrated additive injection 0,0075 l/h - 8.75 l/h
Stroke volume ~ 0,225 l
Con..
The standard dosing range D07 meets the dosing requirements for flow rates from 5 to 700 l/h.
Proportional dosing and without electricity
Proportionality dependent on water flow
Compact ergonomics
Outlet injection
Specifications:
Injection range 0,8 - 5,5% [1:128 - 1:18]
Water flow range 5 l/h - 0,7 m3/h
Operating water pressure 0,3 - 6 bar
Concentrated additive injection 0,8 l/h - 38,5 l/h
Stroke volume ~ 0,225 l
Connectio..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
More reliable, more resistant to chemicals, very easy to maintain without tools...
DOSATRON® presents the new special fertigation dosing pump, the latest addition to the Green Line dedicated to irrigation systems. It operates on irrigation networks from 500 l/h to 9 m3/h. Fertilizers and products, liquid or soluble, conventional or organic, are injected over a dosage range of 0.2% to 2% and 1% to 5%.
The fertigation reference
Ideal in..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
This Water-Powered Nutrient Delivery System DAB Starter Kit includes all the parts you need for the inlet of your Nutrient Delivery System, and is used in in conjunction with DAB Pumps, or pumps with VFD Control. The Nutrient Delivery System DAB Starter Kit does not include a pressure regulator – for systems with inconsistent or high pressure situations, the Standard Starter Kit should be used.
To Complete the LO-FLO Nutrient Delivery System, you will a..
This Water-Powered Standard Starter Kit includes all the parts you need for the inlet of your Nutrient Delivery System and is mainly used for high pressure situations. For systems using DAB Pumps or pumps with VFD Control, the HYKSTART-DAB can be used.
To complete the LO-FLO System, you will also need Dosatron Injectors, Mixing Chamber Kit(s), the pH/EC Monitor Kit or END Kit, and the Water Hammer Arrestor Kit.
Features:
Union
Check..
Water-Powered Nutrient Delivery System Mixing Chamber Kit enhances the blending as the solution passes through. It's a must for silicates. To complete the LO-FLO system, you will also need Dosatron Injectors, the DAB Starter Kit or Standard Starter Kit, Monitor Kit or END Kit, and Water Hammer Arrestor Kit.
Features:
Union
Mixing chamber
Nipples
Seal thread tape
Please note: Parts ordered may look slightly different than the pictu..
This Water-Powered Nutrient Delivery System Monitor Kit measures and displays the well-blended outgoing solution providing peace of mind.
To complete the LO-FLO Nutrient Delivery System, you will also need Dosatron Injectors, the DAB Starter Kit or Standard Starter Kit, Mixing Chamber Kit(s), and the Water Hammer Arrestor Kit.
Features:
Union
Close nipples
Nipples
Tee
Pressure gauge tee
Pressure gauge
Cross
Che..
Water hammer arrestor kits are used to prevent the potential damaging effects of water hammer which is defined as a pressure surge or wave caused when a fluid in motion is forced to stop or change directions suddenly.
Please note: Parts ordered may look slightly different than the picture displayed, but the fit and function will be the same.
Features:
3/4" MPT
6.5" tall
Stainless steel water hammer arrestor
Nipple
Tee
Elbo..
GroLab™ Doser Kit is a powerful grow controller that allows to fully monitor and automate the feeding solution of your plants. Nutrients control, pH correction, water level warnings, auto tank refill, are some functions of this kit.
This kit also provides the necessary tools to create security systems to react and/or notify if any issues arise.
Remote control, real-time notifications, IP cameras integration... are just some of the perks you get with GroL..
Intelligent Control
Doses up to 9 nutrients, additives and pH
Four (24 VDC) outputs available for irrigation if not used for nutrients.
Controls all growing methods - NFT, DFT/DWC, soil, media, drip, and aeroponics.
Proportional dosing rapidly adjusts between irrigations.
Sequential pump control allows each additive time to mix.
Displays EC, CF, TDS, ˚C, ˚F, pH
Set different Conductivity (EC) for day and night.
Water level control..
Easily connect IntelliDose into Edenic cloud software.
The IntelliLink provides internet connectivity to Bluelab Intelli devices, including IntelliDose. With IntelliLink, you can remotely access these systems via Edenic software.
Connects Bluelab IntelliDose Controller to the internet
Connect to your local router via Ethernet cable or Wi-Fi
Get your intelli-data on your mobile device
Remotely change recipes or parameters
Multiple devi..
The Bluelab Peristaltic Pump 1400ml was designed with improved pump performance and ease of maintenance in mind
Peristaltic Pump for Bluelab IntelliDose Controllers that doses up to 1400ml per minute
Requires no tools to replace the squeeze tube
The spring-loaded roller block design enhances both performance and squeeze tube life
Why Peristaltic Pumps?
Affordable commercial dosing volume
Des..
The Bluelab Peristaltic Pump 450ml was designed with improved pump performance and ease of maintenance in mind
Peristaltic Pump for Bluelab IntelliDose Controllers that doses up to 450ml per minute
Requires no tools to replace the squeeze tube
The spring-loaded roller block design enhances both performance and squeeze tube life
Why Peristaltic Pumps?
Affordable commercial dosing volume
Desig..
Measure the nutrient levels in your solution accurately and reliably
This probe is a direct replacement for the EC probe on the Bluelab IntelliDose Controller
With an accurate EC sensor, you can measure electrical conductivity (EC) in your solution and ensure crops are getting the right amount of nutrients they need to thrive
Wire configuration: Black, White, Red..
Direct replacement for the Intelli Range power supply 24DC 2.5A
Over time, power supplies can become unreliable. It is always good to have an extra power supply on hand. Available in global plug types.
This power supply is a direct replacement for the power supply on the following devices:
Bluelab IntelliDose Controller
IntelliClimate
Technical Specification: 100-240VAC, 50/60Hz, 1.4-0.7A Input; 24V 2.4A, 60W Max Output..
The Superpro AC-1 is a simple solution to controlling temperature, humidity and CO2 inside the growing area, giving you a perfect balance between cost and accuracy.
AC-1 contains a built-in photocell that can activate a CO2 device during the day and is coordinated with the exhaust fans so as CO2 stops emitting when fans come on.
Note: CO2 levels must be measured and regulated by user.
Modes
Mode A: LOWER temperature and DECREASE humidity indepen..
The Superpro DDAC-1 receives information from the sensors and activates external fans, air conditioners, dehumidifiers, heaters, and CO2 equipment as needed to maintain optimum levels for indoor agriculture. Until now, this simple idea was easier said than done.
A 15-amp / 120 or 10-amp / 240 vot circuit breaker and heavy-duty internal construction ensures that the unit will operate for years without fail. We only use high-quality UL / CE listed component..
The Maxi Controller can adjust the output according to the ambient temperature: the lamps are dimmed automatically when the temperature exceeds a maximum pre-defined level.
Using the DimLux with a Maxi Controller enables you to plug the DimLux directly into a wall socket without needing an intervening relay, time delay unit or time switch – which saves you costs.
A DimLux controlled by a Maxi Controller is the only (digital) ballast that does not need to..
Perfect for the AutoGrow IntelliDose system and AutoGrow Mini Dosers An affordable, highly accurate dosing pump for use with the AutoGrow IntelliDose system and both AutoGrow Mini Dosers (EC and pH) single unit...
The new Mini Doser EC nutrient controller can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel.
The controller continuously measures the nutrient concentration in the mixing tank and adds A and B nutrients as required to maintain the EC set point. The controller counts the number of doses and in theevent of the dose count per hour exceeding a set value and alarm can be sounded...
The new Mini Doser continuously measures the pH in the mixing tank and adds either pH lower (acid) or pH raise (alkali) as required to maintain the pH set point. The controller counts the number of doses and in the event of the dose count per hour exceeding a set value an alarm can be sounded. In addition alarms can be set to sound should the pH wander outside user set limits. If the dose count per hour exceeds a user setting, the controller will stop dosi..
Feature packed
This hydroponic doser sets a new benchmark in the small dosing controller market. The Intelli-Dose is absolutely feature packed to enable it to cope with just about any hydroponic system. Just take a look at the specification overleaf.
Simple to operate
The secret to its simplicity is that the controller can be configured to suit various systems and when this is done all of the irrelevant settings disappear from the..
These are great little machines aimed at the budget conscious and those who don't need a computer interface. Ideal for hobby gardeners, schools, etc. Even large commercial growers use them - particularly for water pre-treatment (pH) or if they have a trial area with a number of reservoir tanks.
The new Mini Doser can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel...
These are great little machines aimed at the budget conscious and those who don't need a computer interface. Ideal for hobby gardeners, schools, etc. Even large commercial growers use them - particularly for water pre-treatment (pH) or if they have a trial area with a number of reservoir tanks.
The new Mini Doser can work in units of EC, CF or TDS. The complete kit comes with a sensor and two economy solenoid valves pre-wired on a small panel...
The irrigation timer is used to control a pump for irrigating crops.
This timer is ideal for scheduled Ebb & Flow systems and normal irrigation droplets or NFT systems.
The pulse time and the interval time can be set separately for day and night irrigation. The unit comes complete in a waterproof housing with hinged lids, compatible mains sockets and a built in light sensor with 4m low voltage cable which detects day/night-time; making it the perfect ..
The Bluelab Dosetronic keeps tight control of your vital nutrient solution levels automatically so you have the freedom to tend to the daily needs of your crop.
This is the ultimate answer for accurate and automatic control of EC, pH and temperature in hydroponic systems. The controller is easily programmed with the required values for pH, conductivity and temperature. The dosing intervals are set according to the size of the tank and then it’s ..
The Bluelab Dosetronic keeps tight control of your vital nutrient solution levels automatically so you have the freedom to tend to the daily needs of your crop.
This is the ultimate answer for accurate and automatic control of EC, pH and temperature in hydroponic systems. The controller is easily programmed with the required values for pH, conductivity and temperature. The dosing intervals are set according to the size of the tank and then it’s ..
The CARBON -B1 is designed to cost-effectively control the CO2 level inside a growing area. An extremely accurate NDIR CO2 PPM sensor (part-per-million meter) is combined with a digital microprocessor to create an accurate and simple method to control supplemental CO2 use in a greenhouse. The unit can control CO2 levels up to 2500PPM. The user selects the desired CO2 level to be maintained.
A built-in photocell automatically activates the unit only during..
The GI professional CO2 monitor/controller combines the very latest technology with plug and play operation. We have added a photosensor to detect light and dark, this automaticaly changes the working mode of the controller. Other features include: fully adjustable between 0-2000ppm, wall mountable, extremely accurate external sensor with 3 meter cable & automatic calibration.
The GI controller can be used with CO2 generators, CO2 injection devices, s..
The Ultimate CO 2 Controller.
• Simple to use.
• Four separate modes of operation.
• Can be used with or without Analyser.
• Latest Microprocessor technology.
• Intelligent Multi Stage CO 2 dosing.
• Wall mountable.
• User friendly.
• Full 1 year warranty.
• Low Cost
Carbon Dioxide is one of the most important factors in an indoor growroom or glass house. Photosynthesis is the term used to describe the process by which plants combine CO 2 molecul..
A simple to use, innovative CO² sensor and controller, the Harvest Master CO² Easi Controller monitors the growing environment of your grow room – vital for healthy plant growth!
The operation of CO2 EASi.
CO2 EASi is intelligent control of CO2 and at the same time, an Intelligent Temperature controller when the COOL KIT is attached.
In Light ON periods (Day):
The controller will try to maintain Max co2 high PPM for the longest duration. It aggressively..
Gravity feed and main pressure irrigation controller
The PLANT!T® Water Timer can be used with mains water from a tap outlet or with a gravity feed system from a tank, water butt or reservoir. Simply select the time you want the water supply to be turned on and off, link up to your irrigation dripper line and the timer will do the rest.
Key Features:
2 easy steps to programme – turn RUN TIME dial to desired irrigation time and turn FRE..
The Imperium is a precision feed controller, which offer’s greater control over feeding duration and frequency to match each life-stage in a plants growth. Ideal as part of an irrigation system to water plants for the exact amount of time needed. It allows you to feed little and often which will produce maximum yields and allows the use of more oxygen rich media such as a 50;50 mix of Coco and Clay pebbles that would normally dry out without more regular f..
The Imperium Plus is a precision feed controller featuring an integrated Grasslin segmental timer that can be set to run from as little as 1 second up to 15 minutes, at the push of a button which offer’s greater control over feeding duration and frequency to match each life-stage in a plants growth. Ideal as part of an irrigation system to water plants for the exact amount of time needed. It allows you to feed little and often which will produce maximum yi..
(European version: requires plug adapter)
The D1-PPM Carbon Dioxide controller provides high-end performance, at economy pricing.
Starts by using a highly accurate NDIR CO2 sensor. The CO2 Sensor is located in a remote sensor enclosure that can be positioned up to 5 meters from the main controller.
Included inside the remote sensor enclosure is also a photocell which will detect light levels to activate the CO2 control function ONLY when desired by the ..
Clever monitoring, dosing and data logging of solution pH levels. Made easy.
Sometimes the more you know, the better. And when it comes to managing the pH of your nutrient solution, exact knowledge makes a world of difference.
Our brainy pH controller connect constantly monitors and fine-tunes the pH levels for you. But more than that, it wirelessly data logs to your computer too, putting continuous information at your fingertips. Use the data to make sy..
Please see new version, this version is no longer available.
Fully Automated pH Control of Aqueous Solutions
The pH control dosing pump from prosystemaqua provides fully automated pH control of aqueous solutions in hydroponic and aquaponic systems.
It has been designed specifically for the control of pH in mixing tanks for fertilisation. Its small and precise flow allows for very accurate control of pH levels in your hydroponic system.
It comes fully e..
The DV-101A is a multifunctional analogue seconds time clock that helps you to water crops time controlled.
Specifications
Dimensions in mm: 210 x 140 x 110.
Voltage: 230 V AC/ 50 Hz.
Max. power: 5 Amps.
Isolation level: IP-44..
The DV-101D is a multifunctional digital seconds time clock that helps you to water crops time controlled.
Specifications
Dimensions in mm: 210 x 115 x 110.
Voltage: 230 V AC/ 50 Hz.
Max. power: 6 Amps.
Isolation level: IP-44
Item NR: S1010..
EndoSan Hydrogen Peroxide test strips are simple and quick to use. They quickly measure peroxide levels in water and provide a visual aid to ensure enough EndoSan is in use.
The low range test strips measure peroxide levels up to 100ppm.
How to use:
Dip for 2 seconds
Shake
Wait 30 seconds
Compare to testing chart
Each vial contains 100 test strips...
EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.
EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.
When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.
Key Benefits
Highly effective biofilm remover
Unrivalled s..
EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.
EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.
When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.
Key Benefits
Highly effective biofilm remover
Unrivalled s..
EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.
EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.
When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.
Key Benefits
Highly effective biofilm remover
Unrivalled ..
The CCH2O X Growlink Nutrient Dosing System Makes Dosing Easy as 1, 2, 3
1. Install with Under Current® System or Reservoir
2. Add Cultured Solutions®
3. Download App & Connect to Tablet or Smartphone
Monitor & Dosing – pH PPM DO Temp
Smart Water Wireless Nutrient Controller
pH, EC/PPM, DO & Temp Probes
2x Tank Level Switches
5x Remote Dosing Pumps (80L/min)
Nutrient Injection & Probe Manifol..
The small & precise flow of the MP810 provides fully automated pH control of aqueous solutions in the hydroponic systems. It has been specifically designed to control the pH in mixing tanks for fertilization.
The peristaltic pump allows you to maintain the ideal pH values in your tank. After selecting the desired pH setting from 5.5 to 9.5 pH, the pH controller measures the pH value of the solution & automatically adds pH adjustment (acid or alkal..
A stock concentrate powder for fertilizer injectors. DOS A – DOS is a two-part concentrated nutrient formula for use with proportionate mixers (DOSATRON). It is the same great quality as our one-part base just divided into two-parts to maintain balance as a stock concentrate. At a dilution rate of 1:100, 100 lbs of DOS will treat 12,000 gallons of water.
The concentrate containers will be mixed as follows: Part A: 360 grams/gallon Part B: 240 grams/gallon..
A stock concentrate powder for fertilizer injectors. DOS A – DOS is a two-part concentrated nutrient formula for use with proportionate mixers (DOSATRON). It is the same great quality as our one-part base just divided into two-parts to maintain balance as a stock concentrate. At a dilution rate of 1:100, 100 lbs of DOS will treat 12,000 gallons of water.
The concentrate containers will be mixed as follows: Part A: 360 grams/gallon Part B: 240 grams/gallon..
Provide increased quality, along with making the process of blending and dispensing nutrients easier and more accurate.
The Nutrient Delivery System is a simplistic system made up of four main panel sections which can be arranged to accommodate a wide variety of fertigation programs. With total control in mind, customizing the entire panel is easy based on your personal nutrient program! The Nutrient Delivery System thrives anywhere, from greenhouse envir..
Maintaining the correct pH of plant soil or hydroponics nutrient solution is an ongoing task. Macro and micro nutrients, as well as calcium and magnesium bloom boosters, require the correct pH for absorption into the plants root system.
The HI-981412 Groline pH Dosing System, easily assimilates into a nutrient/fertiliser system for soil and hydroponics.
It precisely monitors the pH using the HI-10063 pH/temperature probe and simultaneously controls the a..
Maintaining the correct pH of plant soil or hydroponics nutrient solution is an ongoing task. Macro and micro nutrients, as well as calcium and magnesium bloom boosters, require the correct pH for absorption into the plants root system.
The HI-981412 Groline pH Dosing System, easily assimilates into a nutrient/fertiliser system for soil and hydroponics.
It precisely monitors the pH using the HI-10063 pH/temperature probe and simultaneously controls the a..
HI-981412-00 GroLine pH dosing system with HI-10063 pH probe
Maintaining the correct pH of plant soil or hydroponic nutrient solution is an ongoing task. Macro and micro nutrients, as well as calcium and magnesium bloom boosters, require the correct pH for absorption into the plants root system.
The HI-981412 Groline pH Dosing System, easily assimilates into a nutrient/fertiliser system for soil and hydroponics.
It precisely monitors the pH using the HI..
HI-981413-00 GroLine EC/TDS/Temp Nutrient dosing system with HI-30033 conductivity probe
The HI-981413 uses an amperometric conductivity sensor for measuring the amount of fertiliser in the solution. The meter can be programmed to display results as EC (electrical conductivity) or as TDS (total dissolved solids). The EC results are displayed as mS/cm while TDS is displayed as ppm with a selectable conversion factor from 0.45 to 0.99.
The HI-981413 was de..
The HI-981413 uses an amperometric conductivity sensor for measuring the amount of fertiliser in the solution. The meter can be programmed to display results as EC (electrical conductivity) or as TDS (total dissolved solids). The EC results are displayed as mS/cm while TDS is displayed as ppm with a selectable conversion factor from 0.45 to 0.99.
The HI-981413 was developed to be an inexpensive solution for the horticulturist to maintain the ideal fertili..
The HI-981413 uses an amperometric conductivity sensor for measuring the amount of fertiliser in the solution. The meter can be programmed to display results as EC (electrical conductivity) or as TDS (total dissolved solids). The EC results are displayed as mS/cm while TDS is displayed as ppm with a selectable conversion factor from 0.45 to 0.99.
The HI-981413 was developed to be an inexpensive solution for the horticulturist to maintain the ideal fertili..
Was £350 - Now £300
The Superpro AC-1 is a simple solution to controlling temperature, humidity and CO2 inside the growing area, giving you a perfect balance between cost and accuracy.
AC-1 contains a built-in photocell that can activate a CO2 device during the day and is coordinated with the exhaust fans so as CO2 stops emitting when fans come on.
Note: CO2 levels must be measured and regulated by user.
Modes
Mode A: LOWER temperature and DECR..
The fertilization reference
More efficient
An optimized design
Really adapted to the evolution of practices and treatments
Highly ergonomic adjustment
Specifications:
Injection range 0,03 - 0,3 % 1:3000 - 1:333]
Water flow range 10 l/h - 3 m3/h
Operating water pressure 0,3 - 6 bar
Concentrated additive injection 0,003 l/h - 9 l/h
Stroke volume ~ 0,53 l
Connections NTP-BSP 3/4'' M Ø 20x27mm
Hose PE Ø 4x6 - Lg 1,75m..
The D20 GL range meets treatment needs from 1 to 20 m3.
Proportional dosing and without electricity
Proportional dosing dependent on water flow
Specifications:
Injection range 0,2 - 2 % [1:500 - 1:50]
Water flow range 1 - 20 m3/h
Operating water pressure 0,12 - 10 bar
Concentrated additive injection 2 - 400 l/h
Stroke volume ~ 5 l
Connections Compression fittings Ø 63mm PE
Hose PVC Ø 16x22mm - Lg 1,80m..
The standard dosing range D07 meets the dosing requirements for flow rates from 5 to 700 l/h.
Proportional dosing and without electricity
Proportionality dependent on water flow
Compact ergonomics
Outlet injection
Specifications:
Injection range 0,15 - 1,25 % [1:666 - 1:80]
Water flow range 5 l/h - 0,7 m3/h
Operating water pressure 0,3 - 6 bar
Concentrated additive injection 0,0075 l/h - 8.75 l/h
Stroke volume ~ 0,225 l
Con..
The standard dosing range D07 meets the dosing requirements for flow rates from 5 to 700 l/h.
Proportional dosing and without electricity
Proportionality dependent on water flow
Compact ergonomics
Outlet injection
Specifications:
Injection range 0,8 - 5,5% [1:128 - 1:18]
Water flow range 5 l/h - 0,7 m3/h
Operating water pressure 0,3 - 6 bar
Concentrated additive injection 0,8 l/h - 38,5 l/h
Stroke volume ~ 0,225 l
Connectio..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
More reliable, more resistant to chemicals, very easy to maintain without tools...
DOSATRON® presents the new special fertigation dosing pump, the latest addition to the Green Line dedicated to irrigation systems. It operates on irrigation networks from 500 l/h to 9 m3/h. Fertilizers and products, liquid or soluble, conventional or organic, are injected over a dosage range of 0.2% to 2% and 1% to 5%.
The fertigation reference
Ideal in..
Installed on the water network, the DOSATRON uses water pressure as the only driving force. When activated, it sucks in the concentrated product, doses it to the desired percentage, then mixes it with the driving water. The solution is then sent downstream. The dose of product injected is always proportional to the volume of water flowing through the DOSATRON, regardless of variations in flow rate or system pressure.
Externally adjustable proportional d..
This Water-Powered Nutrient Delivery System DAB Starter Kit includes all the parts you need for the inlet of your Nutrient Delivery System, and is used in in conjunction with DAB Pumps, or pumps with VFD Control. The Nutrient Delivery System DAB Starter Kit does not include a pressure regulator – for systems with inconsistent or high pressure situations, the Standard Starter Kit should be used.
To Complete the LO-FLO Nutrient Delivery System, you will a..
This Water-Powered Standard Starter Kit includes all the parts you need for the inlet of your Nutrient Delivery System and is mainly used for high pressure situations. For systems using DAB Pumps or pumps with VFD Control, the HYKSTART-DAB can be used.
To complete the LO-FLO System, you will also need Dosatron Injectors, Mixing Chamber Kit(s), the pH/EC Monitor Kit or END Kit, and the Water Hammer Arrestor Kit.
Features:
Union
Check..
Water-Powered Nutrient Delivery System Mixing Chamber Kit enhances the blending as the solution passes through. It's a must for silicates. To complete the LO-FLO system, you will also need Dosatron Injectors, the DAB Starter Kit or Standard Starter Kit, Monitor Kit or END Kit, and Water Hammer Arrestor Kit.
Features:
Union
Mixing chamber
Nipples
Seal thread tape
Please note: Parts ordered may look slightly different than the pictu..
This Water-Powered Nutrient Delivery System Monitor Kit measures and displays the well-blended outgoing solution providing peace of mind.
To complete the LO-FLO Nutrient Delivery System, you will also need Dosatron Injectors, the DAB Starter Kit or Standard Starter Kit, Mixing Chamber Kit(s), and the Water Hammer Arrestor Kit.
Features:
Union
Close nipples
Nipples
Tee
Pressure gauge tee
Pressure gauge
Cross
Che..
Water hammer arrestor kits are used to prevent the potential damaging effects of water hammer which is defined as a pressure surge or wave caused when a fluid in motion is forced to stop or change directions suddenly.
Please note: Parts ordered may look slightly different than the picture displayed, but the fit and function will be the same.
Features:
3/4" MPT
6.5" tall
Stainless steel water hammer arrestor
Nipple
Tee
Elbo..
GroLab™ Doser Kit is a powerful grow controller that allows to fully monitor and automate the feeding solution of your plants. Nutrients control, pH correction, water level warnings, auto tank refill, are some functions of this kit.
This kit also provides the necessary tools to create security systems to react and/or notify if any issues arise.
Remote control, real-time notifications, IP cameras integration... are just some of the perks you get with GroL..
Intelligent Control
Doses up to 9 nutrients, additives and pH
Four (24 VDC) outputs available for irrigation if not used for nutrients.
Controls all growing methods - NFT, DFT/DWC, soil, media, drip, and aeroponics.
Proportional dosing rapidly adjusts between irrigations.
Sequential pump control allows each additive time to mix.
Displays EC, CF, TDS, ˚C, ˚F, pH
Set different Conductivity (EC) for day and night.
Water level control..
Easily connect IntelliDose into Edenic cloud software.
The IntelliLink provides internet connectivity to Bluelab Intelli devices, including IntelliDose. With IntelliLink, you can remotely access these systems via Edenic software.
Connects Bluelab IntelliDose Controller to the internet
Connect to your local router via Ethernet cable or Wi-Fi
Get your intelli-data on your mobile device
Remotely change recipes or parameters
Multiple devi..
The Bluelab Peristaltic Pump 1400ml was designed with improved pump performance and ease of maintenance in mind
Peristaltic Pump for Bluelab IntelliDose Controllers that doses up to 1400ml per minute
Requires no tools to replace the squeeze tube
The spring-loaded roller block design enhances both performance and squeeze tube life
Why Peristaltic Pumps?
Affordable commercial dosing volume
Des..
The Bluelab Peristaltic Pump 450ml was designed with improved pump performance and ease of maintenance in mind
Peristaltic Pump for Bluelab IntelliDose Controllers that doses up to 450ml per minute
Requires no tools to replace the squeeze tube
The spring-loaded roller block design enhances both performance and squeeze tube life
Why Peristaltic Pumps?
Affordable commercial dosing volume
Desig..
Measure the nutrient levels in your solution accurately and reliably
This probe is a direct replacement for the EC probe on the Bluelab IntelliDose Controller
With an accurate EC sensor, you can measure electrical conductivity (EC) in your solution and ensure crops are getting the right amount of nutrients they need to thrive
Wire configuration: Black, White, Red..
Direct replacement for the Intelli Range power supply 24DC 2.5A
Over time, power supplies can become unreliable. It is always good to have an extra power supply on hand. Available in global plug types.
This power supply is a direct replacement for the power supply on the following devices:
Bluelab IntelliDose Controller
IntelliClimate
Technical Specification: 100-240VAC, 50/60Hz, 1.4-0.7A Input; 24V 2.4A, 60W Max Output..